Legrand MRR2 Instrukcja Użytkownika Pobierz pdf

ADVANCED OPERATION

Assigning Occupancy Emulation to a House Scene

You can assign the repeater’s occupancy emulation function to a Miro House

Scene button. This is very convenient, especially if the repeater is installed in a

hard to reach area.

1. From a wireless house scene controller (MRD5 or MRH5), press

until its

LED begins ﬂashing (about 2 seconds).

2. Press the scene button you want to use. We recommend the fourth one. The

LEDs on all the Miro wireless devices begin to ﬂash. You now have 10 minutes

to complete this process.

3. Go to the repeater and press both buttons for 2 seconds until the repeater

status LED blinks yellow.

IMPORTANT: Only one repeater should be assigned to the house scene

button. If you have more than one repeater, use the most centrally located.

4. Check all the Miro wireless device LEDs. If they are blinking yellow, they are

assigned to the selected scene button. To exclude a device from the scene

press

on the device until the LED begins to ﬂash green.

Yellow ﬂashing LED = Included in the active scene

Green ﬂashing LED = NOT included in the active scene

If a device LED is NOT ﬂashing, the 10 minute binding process timer may have

expired. Go back to step 1 and repeat.

5. Return to the house scene controller used in step 1.

Press for 2 seconds — the status LED stops ﬂashing, then all the status

LEDs in the house turn to solid green.

6. From the same house scene controller, press and hold the same scene button

until the LED ﬂashes once (about 2 seconds). Scene recording for this button

is complete.

7. When you leave the house, press the House Scene button you just recorded.

One minute later, occupancy emulation will begin.

1 2 3 4 5 6 7 8 9

Podsumowanie treści

Strona 1 - ADVANCED OPERATION

ADVANCED OPERATIONAssigning Occupancy Emulation to a House SceneYou can assign the repeater’s occupancy emulation function to a Miro House Scene butto

Strona 2 - TROUBLESHOOTING

CLEANINGClean using only a cloth dampened with water and a little mild detergent.Use of solvents or hydrocarbon-based cleaners may cause permanent dam

Strona 3 - FCC NOTICE

FCC NOTICEThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

Strona 4 - Installation Instructions

MRR2Wireless RepeaterSpecificationsMRR2InputVoltage ... 9-12VDC,50mAminimumAC-DCadaptor(provided) Input120VAC,60Hz Out

Strona 5 - UNIT DESCRIPTION

UNIT DESCRIPTION Use the Miro™ MRR2 Wireless Repeater in large installations, where the standard range (approximately 25m/80’)isinsufcient,orinb

Strona 6 - INSTALLATION

INSTALLATION1. Locate the repeater in a central location, taking into consideration both the horizontalandverticalspaceinthehome.Ina2-story

Strona 7 - SET HOUSE ID

SET HOUSE IDAllMirowirelessdevicesinstalledinthesamehomemustacquirethesameunique House ID before use. This process is known as house bind

Strona 8 - OPERATION

OPERATIONWireless Range BoostOnce the repeater is bound to the House, it automatically receives and retransmits all wireless Miro network trafﬁc in th

Strona 9

4-FOLD•Print:2-sides•InkColor:Black•Paper:White16lb(60g/msq) Uncoated, prefer recycled stock•Finaltrimsize:16”(Wide)x6”(High).•Fou